No Water In Shower But Sinks Are Fine (7 Awful Reasons!)

18 Min Read
No Water In Shower But Sinks Are Fine

Having no hot water in your shower can be really annoying but don’t panic, this is a common issue and it’s usually easy to remedy.

So if you’re experiencing the frustration of not having water coming out of your shower, while the sinks are working fine, you’ve come to the right place!

Read on for tips to get your shower back up and running again quickly.

If you experience a situation where there is no water coming out of the shower but the sinks are functioning properly, it could be due to a clogged aerator or broken pipe. You should first check if any of the shutoff valves on either side of the wall have been closed and if they are open, then check for any blockages in the pipes connected to your shower. If this does not solve your problem you may need professional help as a plumber can inspect for more complex issues such as blocked drains or faulty plumbing installations.

Why is there no water in my shower only?

If you have no water in your shower but the sinks are fine, it could be due to a variety of causes.

One common cause is clogged or blocked pipes.

This can happen if there is debris that has built up inside the pipes over time, restricting or blocking them off completely.

Issue with your hot water heater or cold water supply:

Another reason could be an issue with your hot water heater or cold water supply. If these components aren’t functioning properly, then it may prevent any water from reaching your shower head at all.

Issues with valves and fixtures:

Finally, issues with valves and fixtures can also cause low pressure in the shower and result in no water coming out at all.

Check to make sure that nothing has come loose or disconnected within the walls since improper connections can lead to problems like this as well.

If none of these potential causes seem likely, then you should contact a professional plumber for assistance as soon as possible so they can assess and address any underlying issues causing this problem in your bathroom’s plumbing system.

Causes of No Water in Shower:

Blocked or defective diverter valve:

One of the most common causes of no water in the shower but sinks are fine is a blocked or defective diverter valve.

The diverter valve is responsible for directing water from either the faucet or showerhead, depending on where it’s been set.

When there’s a blockage in this pipe, it can stop all water flow to the showerhead while still allowing some to come through for other tap fixtures like sinks and toilets.

Another cause could be an issue with your hot water heater.

If it isn’t working properly, you may not have enough pressure to get sufficient amounts of hot water into your pipes which would then lead to insufficient amounts coming out of your showers and taps.


Additionally, if something has gone wrong with the thermostat that regulates temperature within your tankless system, this too could affect how much warm/hot water comes out when you turn on a tap such as in a bathroom sink or showerhead.

If neither of these two issues seems likely the culprit behind why you’re having trouble getting any water out at all from one specific fixture (in this case – showers).

Then it might be worth looking into whether there’s an obstruction somewhere else along the line between the source and exit point; i.e., anything blocking off access points like valves or bends in piping, etc.

This could include things like debris buildup caused by hard minerals found naturally within some types of plumbing systems as well as foreign objects that have become lodged inside due to misuse over time (i.e., hairballs).

  1. Blocked Drains: If the shower drain is clogged, water will not be able to flow out. This can be caused by a variety of things, such as hair, soap scum, and other debris.
  2. Low Water Pressure: If the water pressure is too low, it can restrict the flow of water to the shower. This can be caused by a variety of issues, such as a leak in the pipes, a closed shut-off valve, or a problem with the main water line.
  3. Broken Faucet: If the faucet is broken, it can cause a decrease in water pressure and an inability to deliver water to the shower.
  4. Broken or Blocked Showerhead: The showerhead can become blocked or broken, preventing water from flowing out.
  5. Faulty Shower Valve: If the shower valve is faulty, it can cause a decrease in water pressure and an inability to deliver water to the shower.
  6. Leaky Pipes: If the pipes leading to the shower are leaking, it can cause a decrease in water pressure and an inability to deliver water to the shower.
  7. Poorly Installed Plumbing: If the plumbing was not installed correctly, it can cause a decrease in water pressure and an inability to deliver water to the shower.

Sink Working Fine Diagnosis:

Sink Working Fine Diagnosis is an important part of determining the cause of a lack of water in a shower, but functioning sinks.

There are several potential causes for this issue and it is essential to narrow down the source before embarking on repairs or replacements.

Checking plumbing fixtures and pipes will be necessary in order to pinpoint the exact cause.

If no visible signs of damage can be found, then it may indicate that there is either an obstruction within one or more lines, or that something has caused a decrease in pressure throughout the entire system.

A common culprit might be sediment buildup which restricts water flow and needs to be cleared out with proper flushing techniques.

Alternatively, pressure could have been reduced by faulty valves connecting lines together; these should always be checked first as they are easily replaced if needed and do not require major reworking of existing plumbing systems.

In some cases, however, blockages cannot simply be flushed out due to their location within pipes or other areas where access is more difficult than normal.

When this happens professional assistance may need to be sought after instead depending on how complicated things actually become during the diagnosis phase.

The bottom line here is that every situation needs its own individual assessment since there could potentially be many reasons why water isn’t flowing properly through showers even though sinks work fine.

Getting help from experienced professionals if required would greatly reduce time spent trying to diagnose such issues correctly otherwise!

Troubleshooting Steps for Shower Lack of Water:

When the shower is not getting enough water, some simple troubleshooting steps can help remedy the problem.

  • First, check to make sure that the water supply valves are open and turned on fully. The valve should be opened all of the way past any stops if present.
  • If it is already open but still no water flow occurs, then a second valve may need to be accessed in order to increase pressure in the line.
  • Another potential issue could be with low pressure due to clogs within either pipes or fixtures such as an aerator. If this is suspected, then disconnecting and cleaning out both faucets and showerheads can help restore full pressure again.
  • Cleaning any hard-water deposits off of them will also improve flow rates over time as well as conserve more energy from being used for wastefully running hot or cold water longer than necessary.

Finally, there may be an issue with a diverter valve causing one side of your plumbing system (the sinks) to have better performance than another (the tub).

Diverter valves often get stuck inside their housing due to mineral buildup over time.

These must be removed and cleaned thoroughly before reinsertion back into place so that proper levels of hydraulic output are maintained across both systems equally once again without interruption or drops in performance anywhere else within your home’s plumbing network overall.

Common Symptoms and Fixes:

No Water In Shower But Sinks Are Fine is a common issue faced by many homeowners. It can be caused by a variety of issues, including clogged pipes, faulty valves, and low water pressure.

The most common symptom of this issue is weak or no water coming out of the showerhead while the sinks are functioning normally. If you experience this issue in your home, there are several things to check before calling a plumber.

First, it’s important to make sure there isn’t an obstruction in the shower head itself or any part of the shower’s plumbing system that could be restricting water flow.

Additionally, if you notice rust-colored stains around fixtures or pipe connections throughout your bathroom, these may indicate corrosion and should be addressed immediately as they can cause serious damage to your plumbing system over time.

You can also inspect for signs that sediment has built up inside pipes or near faucets; if so, these will need to be cleared away with professional help from a qualified technician at once.

For low water pressure problems causing inadequate flow from showers but normal flow from sinks and other outlets on the same circuit, the problem might lie with worn components within either an individual valve mechanism or else at main stop valves located elsewhere in the house where pipework feeds multiple appliances.

A plumber would normally attend the site to assess how best to resolve such matters which often require repair/replacement parts being sourced before work can commence.

No water pressure in the shower but plenty everywhere else:

No water pressure in the shower is one of the most common plumbing issues. It can be caused by a variety of factors, such as clogged pipes, low supply pressure or faulty washers and valves.

In some cases, it’s possible to identify and fix the problem yourself with a few simple tools.

If you’re experiencing a lack of water pressure but still have plenty elsewhere in your home, it’s likely that there’s an issue with your shower faucet or valve.

  • The first step towards diagnosing this issue is to check whether all settings are on “full” – if not, adjust them accordingly before moving onto more complex fixes.
  • If adjustments don’t improve the situation then further investigation may be required.
  • It’s also important to check for any visible blockages in your piping which could reduce water flow throughout your system; these may include mineral deposits from hard water or other objects lodged within the pipe itself,

Both should be cleared using appropriate methods depending on severity and material composition (metal-based objects will require specialist removal).

If all else fails then consulting a professional plumber would be advisable; they’ll have experience dealing with similar problems so won’t struggle too much when solving yours!

How do you unclog a shower diverter?

If you’re experiencing low water pressure or no water at all coming from your shower but the sink is working fine, there may be a clog in the diverter.

The diverter is the part of your plumbing system that helps direct the flow of water to either the faucet or showerhead. If it’s blocked with debris, this can cause a decrease in pressure for your shower and should be checked out immediately.

To unclog a shower diverter, you’ll need some basic tools like pliers and an adjustable wrench.

  1. First shut off the water supply going into your bathroom by turning off the main valve (if you can’t locate yours, consult with a local plumber).
  2. Then remove any screws holding on any parts associated with the tub spout using an adjustable wrench.
  3. After unscrewing these pieces, use needle nose pliers to gently pull out any chunks of dirt or debris lodged in between them which could be causing a blockage.
  4. Finally, inspect all connections for signs of damage and replace as necessary before reassembling everything back together again and restoring power back to your bathroom fixtures.

By following these steps correctly, you should have successfully unclogged your shower diverter!

It’s important to note that if after attempting these repairs yourself you still experience problems with low water pressure or no flow from your tub spout then it might be best to contact a professional who specializes in plumbing services.

Sometimes bigger issues lie beneath what we can see just by looking at our pipes and valves alone!

Why did my shower suddenly stop working?

The most common reason why a shower suddenly stops working is due to a lack of water pressure. This can happen if the pipes supplying water to the shower become clogged or blocked by debris, which restricts the flow of water and reduces pressure.

It could also be caused by an obstruction in the shutoff valves leading to the shower that is preventing them from opening properly and allowing enough water through.

In other cases, it could be because of broken seals or faulty parts within the plumbing system that need repair.

If your sink faucets are still functioning but your shower isn’t, you should check for any blockages first before examining individual components like pipes, washers, and gaskets.

You may even find sediment buildup on these items that might be blocking off part of your plumbing system and causing low water pressure in just one area (the shower).

If this doesn’t solve your problem then it would be best to call in a professional plumber who will have the tools necessary for diagnosing more complicated issues like busted piping or malfunctioning valves.


In conclusion, a lack of water in the shower but not in sinks can be caused by several different issues.

The most common cause is a clogged aerator or hose on the showerhead, which reduces water flow.

Other possible problems include low pressure from an undersized hot water heater, faulty valves, and restricted plumbing lines.

In some cases, these issues can be easily remedied with simple DIY fixes such as replacing parts or removing debris from the pipes.

However, if you cannot identify or repair the issue yourself it may be necessary to call a qualified plumber for assistance to ensure that your home’s plumbing system is functioning properly and safely again.

Share this Article
Leave a comment

Leave a Reply

Your email address will not be published. Required fields are marked *